- 积分
- 2319996
- 兑换点
- 点
- 声望度
-
- 金钱
- 元
- 银行存款
- 元
- 贡献度
-
- 精华
|
发表于 2013-11-14 20:01:22
|
显示全部楼层
本帖最后由 wanghanq 于 2013-11-18 14:10 编辑
此类警告多为“不规范文档”导致。
多数是因不了解 mode 设置的目的而无意操作导致...
误操作导致的器件库问题显然解决办法正如你当前所描述(删除不必要的模式,仅保留Normal模式)。
遇到问题之前帖子提到 最直接的老师是软件自身,
我们拷贝“Extra Pin…in Normal of part ”后在系统自带的 帮助系统不难搜索到需要了解的内容:
(由于软件过于庞大,有时,即使选择了完整安装,如库、帮助等文档也不完整,需要后期手动将帮助文档_记忆中当前官网有下载或之前的帖子中有提到...)
点击 Extra Pin Found in Component Display Mode 可以看到下面的字段(此段内容翻译好的网友不妨帮着翻译下...)
Extra Pin Found in Component Display Mode
This compiler hint appears if an extra pin has been detected in one of the display modes for a part. The message is displayed in
the Messages panel in the following format:
Extra Pin Identifier in DisplayMode of part PartName,
where
Identifier is used to identify the pin in question. When compiling a schematic library document, the identifier appears in the
format PhysicalComponentName-PinDesignator (e.g. DIP14-15). When compiling the source schematic or project, the identifier
appears in the format PartDesignator-PinDesignator (Inferred) (e.g. X1-1 (Inferred)).
DisplayMode is the specific graphical representation mode for the part in which the extra pin has been found. A part has a
Normal mode and can have up to 255 defined Alternate modes
PartName is either the physical component name or the designator for the affected part, depending on whether you are
compiling the schematic library document or source schematic sheet/project respectively.
Default Report Mode
warning
Recommendation 推荐(原因或解决方法)
This violation typically arises when an alternate graphical mode is defined for a component and either:
• An extra pin has been added to the display that is not specified in the Normal display mode or
• A pin has been specified with a different Designator and/or Name to a pin specified in the Normal display mode.
Not only must there be an identical number of pins between graphical display modes, the pins must be identical in both
Designator and Name.
In the source schematic library, display the offending display mode for the component and delete the extra pin. This can be
performed directly on the schematic sheet for a part that has been placed already, but you would typically tackle the problem
from within the library, then push the change across (Tools » Update Schematics).
另:如果你那边有mode模式的应用,不妨给大家讲讲您那边的应用情况
Availability
In SCH Library Editor, click menu Tools » Mode » Remove
Details
A component can have a default representation - called Normal - and up to 255 additional
representations, known as Alternates. First ensure that the component you wish to remove a
graphical representation from is selected in the Components list of the SCH Library panel (and is
therefore the active component in the main design window). Change the current graphical
representation (mode) for the component to the one you wish to remove.
After launching the command, the current graphical representation will be removed from the
component and the previous representation will appear in the main design window.
Notes
You can remove any of the graphical representations (Normal and Alternate) that exist for a
component.
If the component has one or more Alternate representations and you remove the Normal
representation, the first Alternate (Alternate 1) will become the Normal representation. All other
Alternates will be renumbered accordingly.
If the component has no Alternate representations and you remove the Normal representation, only
the graphics will effectively be removed. The Normal representation remains, since a component
must always have at least the default view for its symbol. The main design window will show a blank
sheet, ready for addition of graphics.
附上相关的文档(方面帮助文档不完整的网友查看):
此主题当前不完美的地方:差一个可操作案例(等候您的上传)
|
本帖子中包含更多资源
您需要 登录 才可以下载或查看,没有账号?注册
x
|