请教高手,我从PADS2005SP3 PCB导出ASC时出错

zdhmcu1234

请教各位高手：

　　我在公司用PADS2005SP3软件画的PCB，由于要打板，而做板的公司用的是POWER PCB5.0的版本．所以我从PADS2005SP3将PCB导出为ASC文件，版本为5.0．结果用POWER PCB5.0导入时，有如下的警告信息：

　　Reading file --  E:\mtk(2)\40-TDM610-MAA2X.asc
Drawing piece has wrong number of corners 1   in piece 0
OPEN   1   150000 0  
*Bad lines piece data line format VALUE     -750000           0   0.000  1     1800000      150000 N  RIGHT   DOWN
REGULAR <ROMANSIM STROKE FONT>
*Bad *PARTDECAL* ascii data line format
REF.DES.
drawing name already used VALUE
VALUE     9750000    -3750000   0.000  1     1800000      150000 N CENTER   DOWN
*Bad *PARTDECAL* ascii data line format
REGULAR <ROMANSIM STROKE FONT>
*Bad *PARTDECAL* ascii data line format
VALUE
*Bad *PARTDECAL* ascii data line format
T0     0     0     0   
*Bad *PARTDECAL* ascii data line format
T750000 0     750000 0   
*Bad *PARTDECAL* ascii data line format
T1500000 0     1500000 0   
*Bad *PARTDECAL* ascii data line format
T2250000 0     2250000 0   
*Bad *PARTDECAL* ascii data line format
T3000000 0     3000000 0   
*Bad *PARTDECAL* ascii data line format
T3750000 0     3750000 0   
*Bad *PARTDECAL* ascii data line format
T4500000 0     4500000 0   
*Bad *PARTDECAL* ascii data line format
T5250000 0     5250000 0   
*Bad *PARTDECAL* ascii data line format
T6000000 0     6000000 0   
*Bad *PARTDECAL* ascii data line format
T6750000 0     6750000 0   
*Bad *PARTDECAL* ascii data line format
T7500000 0     7500000 0   
*Bad *PARTDECAL* ascii data line format
T8250000 0     8250000 0   
*Bad *PARTDECAL* ascii data line format
T9000000 0     9000000 0   
*Bad *PARTDECAL* ascii data line format
T9750000 0     9750000 0   
*Bad *PARTDECAL* ascii data line format
T10500000 0     10500000 0   
*Bad *PARTDECAL* ascii data line format
T11250000 0     11250000 0   
*Bad *PARTDECAL* ascii data line format
T12000000 0     12000000 0   
*Bad *PARTDECAL* ascii data line format
T12750000 0     12750000 0   
*Bad *PARTDECAL* ascii data line format
T13500000 0     13500000 0   
*Bad *PARTDECAL* ascii data line format
T14250000 0     14250000 0   
*Bad *PARTDECAL* ascii data line format
T15000000 0     15000000 0   
*Bad *PARTDECAL* ascii data line format
T15750000 0     15750000 0   
*Bad *PARTDECAL* ascii data line format
T16500000 0     16500000 0   
*Bad *PARTDECAL* ascii data line format
T17250000 0     17250000 0   
*Bad *PARTDECAL* ascii data line format
T18000000 0     18000000 0   
*Bad *PARTDECAL* ascii data line format
PAD 0 3
Too many decimal places in number
-2 450000 OF  90.000 1875000 0   0 
*Bad *PARTDECAL* ascii data line format
-1 0   R 
*Bad *PARTDECAL* ascii data line format
0  0   R 
*Bad *PARTDECAL* ascii data line format
PAD 1 3
Too many decimal places in number
-2 450000 RF  90.000 1875000 0   0 
*Bad *PARTDECAL* ascii data line format
-1 0   R 
*Bad *PARTDECAL* ascii data line format
0  0   R 
**INPUT WARNINGS FOUND**　

不知那位能帮忙解决一下，不胜感激！

jordan23

应该是中文字型的问题

jimmy406

不会转成GERBER文件吗？

ksepan1234

对啊,直接给板厂gerber文件吗

zdhmcu1234

这是个好方法,但问题出来,终得解决啊,希望各位高手帮帮啊