各位高手我在第一层铺铜时出现了一个错误文件:therm.err,我看了一下thermal的设置,spoke的值是2, 并且大多数的过孔都是通地的过孔,请大家分析一下是出现这个错误文件的原因是什么呢? 文件内容如下: Drilled pads with Nondrilled pads with less than 50% thermal extensions less than 50% thermal extensions Report of Thermal Spokes Generator. On Primary Component Side: (5150, 4100) # = 1 D7/QFP.49 (3809.06, 1657.48) # = 1 D2.45 (5248.03, 3988.31) # = 0 (5175, 4000) # = 0 D2.40 (5248.03, 4113.31) # = 1 D2.34 (5248.03, 4263.31) # = 1 (5325, 4275) # = 0 D2.4 (5625.98, 3988.31) # = 1 (5550, 3950) # = 0 D2.1 (5625.98, 3913.31) # = 0 B5.3 (4683, 3950) # = 1 B15.3 (4233, 2900) # = 1 N2.14 (2832.5, 3527.5) # = 0 D4.16 (5562.96, 2784.11) # = 0 D6.48 (5377.03, 1885.85) # = 0 D6.45 (5377.03, 1810.85) # = 1 (5450, 1850) # = 0 (4825, 1825) # = 0 D6.1 (4999.08, 1885.85) # = 1 Total Drilled pads: 6 Total Nondrilled pads: 13 Report of Violating Thermal Spokes Remover. On Primary Component Side: N8.9 (3967.72, 397.64) # = 1 D6.4 (4999.08, 1810.85) # = 0 D6.10 (4999.08, 1660.85) # = 0 D6.12 (4999.08, 1610.85) # = 0 D6.15 (4999.08, 1535.85) # = 0 D6.21 (4999.08, 1385.85) # = 0 D6.28 (5377.03, 1385.85) # = 0 D6.34 (5377.03, 1535.85) # = 0 D6.39 (5377.03, 1660.85) # = 0 D6.45 (5377.03, 1810.85) # = 0 N2.1 (2627.5, 3577.5) # = 1 N5.2 (1899.62, 2252.18) # = 0 D2.4 (5625.98, 3988.31) # = 0 D2.10 (5625.98, 4138.31) # = 0 D2.15 (5625.98, 4263.31) # = 0 D2.21 (5625.98, 4413.31) # = 0 D2.28 (5248.03, 4413.31) # = 0 D2.34 (5248.03, 4263.31) # = 0 D7/QFP.49 (3809.06, 1657.48) # = 0 (5140, 4410) # = 1 (5710, 4160) # = 1 (2350, 2940) # = 1 (5350, 1925) # = 1 (5750, 4425) # = 1 Total Drilled pads: 6 Total Nondrilled pads: 18 Drilled pads with less than 50% thermal extensions
|