新手上路，请教各位，谢谢！

peerless_ww

weisheme 我用ORCAD画好原理图后，生成不了网络表

，出现以下的错误信息，请各位高手指教

Netlist Format: padspcb.dll
Design Name: C:\ORCAD\ORCAD_10.0\TOOLS\数码像框电路图.DSN
ERROR [NET0051]   Duplicate reference found '33'.
ERROR [NET0011]   Netlist failed or may be unusable.
  鄙人乃是新手，谢谢各位！

lanhaiyizhen

有重命名现象,请找一下关于33的错误命名.改掉其中一个即可.

peerless_ww

谢谢高手！我把那些重复的改了，又出了新的错误，很多的，到现在我都不知道怎么改，高手帮帮，多谢啦！

Checking for Invalid References
[DRC0011]   Reference is invalid for this part /U1A:  SCHEMATIC1, PAGE1  (1.00, 0.20)
[DRC0011]   Reference is invalid for this part /U1B:  SCHEMATIC1, PAGE2  (9.10, 0.30)
[DRC0011]   Reference is invalid for this part /U1C:  SCHEMATIC1, PAGE2  (0.90, 0.20)
[DRC0011]   Reference is invalid for this part /U1D:  SCHEMATIC1, PAGE3  (5.30, 0.20)
[DRC0011]   Reference is invalid for this part /12MHz:  SCHEMATIC1, PAGE3  (1.10, 1.00)
[DRC0011]   Reference is invalid for this part /[DRC0011]   Reference is invalid for this part /TI:  SCHEMATIC1, PAGE9  (4.20, 5.20)
[DRC0011]   Reference is invalid for this part /51K:  SCHEMATIC1, PAGE9  (8.10, 3.80)
ERROR [DRC0026]   This reference has already been assigned to a different package type. /U14:  SCHEMATIC1, PAGE5  (2.70, 7.50)
ERROR [DRC0026]   This reference has already been assigned to a different package type. /U14:  SCHEMATIC1, PAGE9  (6.20, 3.80)
ERROR [DRC0027]   Other parts in this package have different values or PCB footprints. /U14:  SCHEMATIC1, PAGE9  (6.20, 3.80)
ERROR [DRC0027]   Other parts in this package have different values or PCB footprints. /U14:  SCHEMATIC1, PAGE9  (3.50, 0.70)

Checking for Duplicate References
ERROR [DRC0010]   Duplicate reference /U14:  SCHEMATIC1, PAGE9  (6.20, 3.80)
ERROR [DRC0010]   Duplicate reference /U14:  SCHEMATIC1, PAGE9  (3.50, 0.70)
WARNING [DRC0034]   Two wires/busses of different nets intersect visually, yet nets are not connected N1220863:  SCHEMATIC1, PAGE9  (5.20, 4.10)

Check Bus width mismatch
  谢谢指导

peerless_ww

请各位高手帮个忙，谢谢！

Design Rules Check
*
********************************************************************************

Checking Pins and Pin Connections
ERROR [DRC0031]   Same Pin Number connected to  more than one net. /U14/1 Nets: 'N1220843' and 'GND'. :  SCHEMATIC1, PAGE9  (5.90, 3.90)
ERROR [DRC0031]   Same Pin Number connected to  more than one net. /U14/2 Nets: 'N1220863' and 'N1186988'. :  SCHEMATIC1, PAGE9  (5.90, 4.10)
ERROR [DRC0031]   Same Pin Number connected to  more than one net. /U14/3 Nets: 'N1220503' and 'M33V'. :  SCHEMATIC1, PAGE9  (5.90, 4.30)
ERROR [DRC0031]   Same Pin Number connected to  more than one net. /U14/ Nets: 'N676509' and 'GND'. :  SCHEMATIC1, PAGE5  (2.90, 7.20)

--------------------------------------------------
Checking Schematic:  SCHEMATIC1
--------------------------------------------------
Checking Electrical Rules
ERROR [DRC0004]   Possible pin type conflict U36,Z0 Output Connected to Output:  SCHEMATIC1, PAGE7  (5.60, 0.10)

  该怎么改